hi I have FWS624G-POE switch. does it have a default IP. If not, then do how do i use telnet to configure in the IP thanks RGod
↧
Brocade FWS 624G-POE
↧
"Output Errors" on turboiron
Hello, We have a turboiron connected to an HP2900 seies switch via a 10Gig SR fibre module. Although the link seems stable, there are a number of "Output Errors" logged on the turbo iron and "FCS Rx Errors" on the HP. Both links are set
↧
↧
Support for IPv6 127-bit subnet mask on point-to-point networks
Hello Community, Running MLXe boxes with 5.3.0b, I was wondering if /127 masks on p2p interfaces were supported ? According to RFC6164, it should be : ftp://ftp.rfc-editor.org/in-notes/rfc6164.txt I have found no mention
↧
ICX6450 access via SonicWall SSL VPN
We just setup a new network and have come across an odd situation. If I am onsite and connected directly to the switch or connected via a wireless AP, I can ping and telnet and web into the Brocade. However, when I am at home and using the
↧
MAC Authentication and 802.1x on same port
Hi all, I am working with Aruba's ClearPass RADIUS server and am trying to configure Brocade switches to do the following: - Authenticate both by MAC authentication as well as 802.1x - If a device fails MAC-auth, then fall back to 802.1x
↧
↧
Brocade 6910 with Cisco 2960
Hello, Our entire network consists of Cisco 2960 and 2960s switches, and for a fiber junction we are using an old 3 Com fiber switch. We are currently utilizing all 12 of the ports on the 3Com fiber switch and we are looking to upgrade. I have
↧
Adding a port to multiple vlans
Hello, I am trying to add a port on a MLX device to multiple existing VLANs. Therefore rather than going into each vlan individually and adding port, is there a way that I can do a vlan range and
↧
VLAN 1
Me again! I have to use Vlan 1 for legacy of my older configuration, I'm doing a transition to another vlan. Problem is on my backbone I cannot seem to make pass the vlan 1 through the trunk. I have 2 routers, the Brocade Backbone
↧
Problems with LACP trunking between Cisco 3750 and Brocade SX1600
Dear all, I'm running out of ideas on how to try and resolve a problem with connecting a Cisco 3750 and a Brocade SX1600 together. So - I've got a simple two port x 1Gethernet connection between these two devices. I want to tagged
↧
↧
where to get recent Brocade MLX MIB-File for SNMP?
I've been looking where to download to SNMP MIB File for Brocade MLX.
↧
Multi Chassis Trunking for VPLS/VLL
Today, Brocade announced its 5.3 release of software for the MLX, XMR, CER, and CES platforms. One of the features I am most excited about is the extension of Multi Chassis Trunking, or MCT, over VPLS or VLL networks. MCT is a key Brocade
↧
Enabling SNMP on NetIron CER
So what is the special secret to allow snmp polling on a NetIron CER? Typically on Brocade/Foundry switches its just "snmp-server community <string> ro" and that is what the config guide shows as well. For some reason I can not get snmp
↧
MRP & STP
Hi all. I was wondering if anybody can share their experience with Brocade's metro-ring protocol and how it affects the spanning-tree topology of the rest of the network. Our network looks (basically) like this. MRP is in red:
↧
↧
Telnet connection slowed
Hi all, I have MLX-32 that I can access remotely via telnet, but lately I have problem access it, the response is slow, the response is delayed. for instance if I issued a command I will have to wait for a second or two before I get the response.
↧
Traffic Manager (TM) Internal Error
Yesterday, i saw a strange problem with my BigIron RX-16, one of its copper module (slot-4) stopped functioning without any alarm, warning messges ... All ports on module were up, but could not communicate with each other ... on detailed
↧
Command for viewing forwarding tables in Foundry switches?
Hi, Is it possible to view the forwarding tables in Foundry switches ? I could not find any command on internet. I know we can use "show ip route" to view the Routing table but did not find command for forwarding table. thanks.
↧
Turboiron x24 uplink port
Good Morning, I'm relatively new to networking and am having difficulty defining an uplink port (that works) on a turboiron x24. I've read the documentation, and done what the doc says but I don't seem to be getting traffic out of the switch. I haven't
↧
↧
are these commands used for finding outgoing interface for a incoming packet.
In order to find a outgoing interface for a incoming packet does the router refer below two commands ? First table to get the mapping of IP-MAC and then to find out from which interface the destination MAC address can be reached. show arp show
↧
Help to config SFP port on FastIron WS 624G ??????????
Hi all! I have 02 FastIron WS 624G (it have 4 moduls SFP, i installed one E1MG-SX on each switch). I used the patch core (LC - LC 50/125) to connect them. That connect between two WS624G , on two switchs had the blue SFP
↧
Interconnect Hp Procurve and BigIron RX-16
I am looking for input on proper spanning tree and vlan configuration I need to connect a BigIron RX-16 to several HP Procurve 'zl' switches. With the RX-16 as the core, which stp should be used and what are the requirements for the vlan id's etc... What
↧