Please suggest the equivalent command in brocade
Hi all Please provide me with the equivalent brocade command for icx6610 for the below cisco commands 1 - vlan access-map test 10
View ArticleSflow on Fesx448??
Hi, Does FESX448 running PREM image support Sflow? I can configure FCX624 and Fcx648 without any issue. But the same settings does not work on the FESX448. This is sh ver SW: Version 07.2.02gT3e3...
View Articleicx-6650 Equivalent Commands
Hi all, Please provide me with the equivalent brocade command for icx6650 for the below cisco commands. interface gigabitEthernet 0/1 no ip unreachables*** no mop enable no ip mask-reply
View ArticleStarlifter - alive or dead?
Hi all, Back awhile ago there was talk of a product code named Starlifter (love that name by the way). Anyway was to do with VM migration across L3 domains in a much reduced time-frame. A quick...
View ArticleICX 6610 stacking and VLAN tagging
I have created an ICX6610 stack with two (2) switches. Stack looks good (show stack detail, stack mac-persistent, same priorities, etc...). Rebooting the primary fails over to the second stack member...
View Articleicx-6450 Equivalent Commands
Hi all, Please provide the equivalent brocade command for icx6450 for the below cisco commands. boot-start-marker boot-end-marker ! security authentication failure rate 10 log security
View ArticleProblem with stacked ICX switches and SNMP monitoring
I use multible stacks of ICX6450 (SW: Version 07.4.00dT7f3) and 6610 switches an cant monitor (Zabbix) them correctly even if i use the MIBs from the "IPMIB_Reference_Jun2013" . Here an example:...
View ArticleMPLS question on MLX
I am new to Brocade and some what new to MPLS. Any help would be appreciated. We get SNMP messages form our monitoring software indicating that a MPLS VLL has gone down. When I do a sho log on the MLX...
View ArticleMigrating From Cisco to Brocade
Current network config Cisco WS-C3750G-12s-s 12 port fiber switch acts as gateway, serves as VTP server; existing vlans are only configured on the Fiber switch, this is propagated to all other...
View ArticleUnable to authenticate via SSH
Hello Everyone, This is my first time using a Brocade router. Traditionally I have been immersed in Juniper and Cisco appliances. So far I am impressed with Brocade hardware. However, I have found...
View ArticleICX6450 Layer 3 license and 10Gig ports
Anyone using ICX 6450 with layer3 license and 10gig port? The 2x10Gig are enabled by default for passing layer 3 traffic or we need license to upgrade from 1gig to 10gig?
View ArticleStrange Dropped ICMP
I'm pinging an interface on an MLXe from another router on a directly connected interface and it receives the echo requests, but appears to be dropping the TX echo replies, with the reason, "Route-only...
View ArticleICX6650-MLXe MCT Client Problem
Hi i have a problem with the client configuration on an ICX6650. The ICX is connected over a static trunk to the MLXe and the ICX is a MCT Member Client Conf ICX: client TOR rbridge-id 13...
View ArticleMLX interface card dont boot up.
Hi everyone! Recently i tried to use NI-MLX-10Gx8-M interface card. Software is Ironware 5.02 We are using 4slot chassi with one BR-MLX-MR2-M. After i plugged the module it eas shown as invalid ....
View ArticleFWS648G to ICX6430C Trunk
I can configure a trunk on my FWS but the ICX doesn't seem to accept a trunk configuration or trunk deploy command. I enter on the FWS: config t turnk e 0/1/39 to 0/1/40 trunk deploy and it's up....
View ArticleICX 6450 license installation
Hi, I am trying to install Layer 3 license in icx6450 scp 201309100zxvdbwFJxxxFHx.xml user@192.168.1.100:license DSA key fingerprint is 81:6e:f8:a7:ee:0a:0e:ae:00:c9:b2xxxxxxx. Are you sure you want...
View ArticleDoes MCT with AIX Servers work?
Has anybody been able to get MCT (MLXe 5.2D) to work with AIX servers (IBM P750, AIX 7100-00-03-1115). I get the LACP-BLOCKED error when I do a show interface. Is there any special config to get this...
View Articlehow can I configure ip routing on FWS624G
How can I configure IP routing on switch FWS624G? This is the show version output: sh version Copyright (c) 1996-2010 Brocade Communications Systems, Inc. UNIT 1: compiled on Apr 19 2010 at...
View ArticleICX6650 and Dell PowerEdge R720xd
I'm having the strangest issue with a new ICX6650 I'm setting up as a top-of-rack switch with a bunch of Dell PowerEdge R720xd servers. Some ports simply don't establish a link (not even the link LED...
View ArticleManagement Interface MLXe and 6650ICX
Hi how can i change the vlan of the Management interface on a MLXe ( Version 5.4.) and ICX Switch Thanks in advance regards Sascha_se
View ArticleVE Port not coming up
I have the following config: lan 1 name DEFAULT-VLAN by port ! vlan 2 by port untagged ethe 1/1/1 router-interface ve 2 ! vlan 30 name ports-2-12 by port tagged ethe 1/1/24 untagged ethe 1/1/3 ethe...
View ArticleTelnet / SSH Source Interface Inactive
Before I take this to TAC, I thought I'd poll the crowd. I'm attempting to set the source interface for Telnet and SSH traffic to loopback 1, which is up/up. loopback 1 192.168.1.1
View ArticleBrocade 6910 VLAN Behavior
Hi All, I have just make an ERP lab using two 6910 switch and one CES switch, using a simple VLAN to test the connectivity between 2 host. But it strange when I change the host port to another port...
View ArticleHowto configure SSH on brocade 64XX series
I want to activate the SSH login to manage my brocade switch. I'm searching the guide and I don't find the command to activate SSH. Do I need to generate a key ? Can you list me all the command I...
View ArticleAdding a port to multiple vlans
Hello, I am trying to add a port on a MLX device to multiple existing VLANs. Therefore rather than going into each vlan individually and adding port, is there a way that I can do a vlan range...
View ArticleICX 6450 24 port switch
I have a ICX 6450 24 port switch that I am trying to partition into 2 layer3 vlans. I created vlan 3 and vlan 13 and added untagged ports 3-12 to vlan 3 and 13 to 23 for vlan 13. vlan 3 by port...
View Articleicx-6450 Need Equivalent Commands
Hi all, Please provide the equivalent brocade command for icx6450 for the below cisco commands. boot-start-marker boot-end-marker ! security authentication failure rate 10 log security
View ArticleBrocade MLX Series and NetIron XMR Series Module Support
Hi all, The the following document be updated to reflex what version of (minimum) code is required to run the line cards?...
View ArticleSwitch 6430-24P
Guys, How can i configure a one single port to Trunk mode ?? I have a Cisco Switch and a Brocade Switch 6430-24p, and I trying to configure an uplink to connect both devices. I set up vlan10 tagged...
View ArticleHardcoding an FCX combo port media type
Does anyone know what the command is to hardcode the media type for one of the combination ports on an FCX box? I can't find it in any of the documentation, and I can't even find it playing around on...
View ArticleHow Fabric Modules Affect The System/BigIron-RX16
Recently I found some strange error message in my box. Some times it will show error from show system fabric-error, but sometimes it disappear.
View ArticleUpgrading Software when Stacked
I have a stack of FCX648S switches. I am familiar with how to upgrade the software (flash and boot) on these devices one at a time, when not in a stack configuration. I also understand that all the...
View ArticleRADIUS + DHCP
Greetings everyone. Do you know if it is possible to use RADIUS server to provide specific DHCP addresses for clients? Can the server based on the authentication credentials provide the specific DHCP...
View ArticleLoading router vs. switch code
Hello, Here is my question. So I am integrating a Brocade solution with about 12 ICX switches this week. They are going to be deployed as layer 2 switches primarily. When asking the customer if I...
View ArticleNon-disruptive restart to SNMP service
Aflter searching this community, there are a few out there that have asked this same question, but it still has never been answered. Now it's my turn. I have an ICX switch that has stopped...
View ArticleVulnerability Scanning with EEye Retina on Brocade switches is failing
We are trying to scan the Brocade switches with Retina and we get several errors, credentails can't be verified, ssh session failed, etc we can from the server SSH into the switch and however when...
View ArticleTelnet to MLX
Configuring a new MLX for the first time, running into a minor issue. On all my other Brocade devices I can telnet to any assigned IP address. For some reason I can't telnet to my MLX on its assigned...
View ArticleNo boot image for x646-PREM6
FEX Boot Code Version 07.2.00T3e5 Enter 'b' to stop at boot ... BOOT INFO: primary does not exist BOOT INFO: secondary does not exist ------ is there anyway to make use to this switch again? please help.
View ArticleChange vlan's netmask on a Super X
Hello, I would like to change an existing vlan's netmask from 255.255.254.0 to 255.255.248.0. What are the steps/syntax? Thanks.
View ArticleNetIron 5.5 Release Date
Dear Community, According to the information I received from my SE, it was due by April !?! Does anyone when NetIron 5.5 will be released ? Maybe someone at Brocade can shed some light to...
View ArticleIP SLA feature
Hello, As far as I know there is no such thing in brocade switches....I need that feature because a customer in the Data Center has a Call Manager installed, and we need to measure the performance...
View ArticleNI-MLX-10Gx8-D
Hi everyone, I'm trying to power on this module in the NetIron MLX-8 and I got this result. NetIron MLX-8 Router#show module
View ArticleSolved: icx6610 etherchannel to cisco 2960g
Hi, I'm evaluating brocade devices and thus new to this side of world. I'm trying to connect a stack of two icx6610 switches to various cisco devices. The layout is like c2960g ----- icx-stack ------...
View Articlehow to delete startup config on FastIron WS without flash image
I have a FastIron 648G which doesn't have a flash image but does have a startup configuration. I can load a flash image via TFTP from the boot menu however I can't seem to do that in conjunction with...
View ArticleSSH/SCP throughput limitation with CER when no rate-limit in place?
We have several CER routers which are displaying throughput issues when using SSH and SCP. These are on completely un-rate limited connections and duplicated in a lab environment where nothing but two...
View ArticleVPLS Auto-discovery endpoints
Hello all, I have a question regarding Auto-discovery......How are the endpoints defined??? just as in a normal VPLS configuration? For example here: Brocade(config)# int loopback 1...
View ArticleIntegrating MRP to VPLS Network
I got case where I want to integrate customer on MRP network to MPLS enabled network as follow. Basicly i want to connect 4K VLAN from MRP network, to customer on 6910. To achive this usually I use...
View ArticleMCT VLANs and non-MCT VLANs
Hello, Attached you will find my diagram.....We have deployed MCT in Distribution layer and MCT in Acces Layer (in each POD). My question and doubt is the difference with MCT VLANs and non-MCT...
View ArticleFCX - where can I see Pause Frame stats?
FCX - Where can I see Pause Frame info? Can I get switch and/or port specific info? I ran show stat eth 1/1/24 - but do not see anything re: pause frames..... Thanks,
View ArticleUpdating a BR6910
Hi, So I just brought a Brocade 6910, (first brocade product I have brought), but I am struggling to find where I download the latest firmware for the device? I would like to update it before I put...
View Article