Quantcast
Channel: Brocade Communities : Popular Discussions - Ethernet Switches & Routers
Viewing all 2370 articles
Browse latest View live

Brocade for Cisco people

$
0
0
Hello,   I am a typical Cisco person...CCNP using Cisco switches and routers at work. We have some Brocade FCX-48GS switches and are planning on moving completely from Cisco switches to Brocade. I have a few questions I need to get answered before

ICX 6450 not booting

$
0
0
So, thinking I was doing a factory reset, I erased the flash primary, secondary and startup-config but now it wont boot because there is no image to boot from.   My first experience with Brocade and obviously that was not the right thing to do. I

MLX16e VLAN Mirroring for Traffic Analysis

$
0
0
I have a pair of MLX16e switches setup as an MCT cluster. I would like to attach an intrusion prevention sensor (IPS) to monitor all VLAN 2 traffic. I believe the sensor will need to receive traffic from each MLX and I have two ports on the ips sensor

startup-config locked

$
0
0
So, I just started at a company that has a couple of fastiron edge switches.  One of them is out of commission, and I am trying to bring it back from the dead.  I was told that the previous net admin bricked the thing and "tried a hack that

BGPv4 BFD Fail-over

$
0
0
hi,   Anyone already done it a configuration BGPv4 with BFD fail-over ?   Because i have make this configuration and BFD don't play, no neighbors visible.   Must Be put on a specific configuration interface in addition to router BGP

Foundry FastIron Edge X448 Premium FESX448-PREM Switch

$
0
0
Hello everyone! I'm new here and new to networking, too. I have so many problems with this switch and hope the community can help me out For this switch I have one 1GigE traffic in/out with /24 IPs on it. My problem, how can I assign one unique IP for

Rate Limiting

$
0
0
Hi! I am looking for the best solution to limit bandwidth on a VE of fastIron superx. if I understand correctly first I should create a traffic policy then modify an extended ACL entry that references the traffic policy and finally bind the ACL to an

Brocade equivalent to cisco CDP

$
0
0
Cisco Discovery Protocol.   Does it exist with brocade?   Thanks

ICX6450-24P Switch and "VLAN Trunking"

$
0
0
Hi, I am new in Brocade world and I am looking for some help with setting up VLAN Trunking/Tagging We have situation here - SonicWall with 3 SonicPoints and 3 different VLANS - 50, 60, 70. (corp, guest, corp5N). SonicWall X4 interface with an IP

Takes 20+ seconds to SSH to a switch

$
0
0
I am setting up 30 switches for a remote site. Everything seems to be working fine. I can ping any switch extremely quickly with 1-3ms response times. However, when I try to SSH to a switch it takes 20+ seconds, and during that time the switch management

Routing interface on 6610

$
0
0
Apologies if this is documented somewhere, I did a good amount of searching and couldn't find how to do it.   Basically I am setting up a "no switchport" equivalent with a 6610, base layer 3 image. I'm able to assign the port an IP, but my problem

Router-Interface command invalid?

$
0
0
Hi,   I am new to Brocade and have our first switch, an FCX648.  I am following the configuration guide about how to setup virtual inerfaces and I am running into troubles, Below is what I am entering based on the config guide example:  

DHCP Server

$
0
0
I am trying to configure a DHCP sever on a FCX running layer 2 software and the "ip dhcp-server" command is not available. I have checked the configuration guide and this feature is supported... Any ideas?

show interface capabilities equilavent for Netirons

$
0
0
Is there a cisco "show interface capabilities" equilavent for Netirons. I need to find out what sfp model is being used on a remote Netiron.   Thanks in advance

PROBLEM WITH DYNAMIC LAG FORMATION OF 4 MEMBERS IN BROCADE MLX AND OTHER VENDOR

$
0
0
Out of four ports configured for lag with other vendor chassis, only two established. Please see below and suggest for any idea.   ort  [Sys P] [Port P] [ Key ] [Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope]

FWS648G - Layer 2 or Layer 3?

$
0
0
Hi everyone,   I have a couple FWS648G switches and I'm trying to determine if they are Layer 2 or Layer 3 switches.  Below is the output from show version.  Thanks in advance for your help!     Copyright (c) 1996-2010 Brocade

Multi Chassis Trunking for VPLS/VLL

$
0
0
Today, Brocade announced its 5.3 release of software for the MLX, XMR, CER, and CES platforms.  One of the features I am most excited about is the extension of Multi Chassis Trunking, or MCT, over VPLS or VLL networks.   MCT is a key Brocade

MAC address leaking through

$
0
0
Hi   I'm trying to get our datacenter hooked up to a Toronto Exchange network (Torix), but unfortunately a problem has come up that I have not been able to find a solution for.   Torix uses port security when allowing others to connect to

switch management (outband management /ssh / telnet)

$
0
0
Hello, I am running L3 image and I have configured the switch outband and added the ip on switch   #interface M1 FastIron(config-if-mgmt)#ip addr 192.168.1.200/24   created vlan 2 allocated port 2 added Ip address 192.168.2.1/24  

TFTP failing with error code 5

$
0
0
Hello,         I am trying to copy my flash to a tftp server in the same subnet as my switch. The tftp server is pingable from my switch and vice versa. I see the TFTP service running in windows Vista (perform netstat -a in
Viewing all 2370 articles
Browse latest View live