How can I configure the Brocade terminal to use Backspace for deleting the character before the cursor? Right now I have to use Ctrl-h to do that and that's really annoying! And how can I configure the terminal length like in Cisco IOS "terminal length
↧
Brocade Terminal configuration
↧
Foundry FastIron Edge X448 Premium FESX448-PREM Switch
Hello everyone! I'm new here and new to networking, too. I have so many problems with this switch and hope the community can help me out For this switch I have one 1GigE traffic in/out with /24 IPs on it. My problem, how can I assign one unique IP for
↧
↧
How to upgrade firmware ?
All our infrastrure is connected to our switch foundry SX800. We would like to upgrade the firmware version from 4.1 to the latest version. Could you tell me: What is the latest version? How much downtime is necessary to do this kind of operation? How
↧
Configure DR for PIM
Anyone familiar with how to configure the DR priority for an interface? I have a mixed environment and am finding that while I can configure the priority on another vendors device and affect the DR election, none of the brocade devices
↧
TFTP failing with error code 5
Hello, I am trying to copy my flash to a tftp server in the same subnet as my switch. The tftp server is pingable from my switch and vice versa. I see the TFTP service running in windows Vista (perform netstat -a in
↧
↧
Routing Protocol
Hi !!! Can I use EIGRP protocol between Cisco router and Brocade router? Thank you in advance. m.kazemi
↧
FWS624GPO factory default reset
I have a FWS624GPOE switch. I have configured the switch but i can be able to get into the admin privilege config mode. i seem to be in the user mode. How can i reset this switch ta factory default more to start configuring it again. please help
↧
Link-up, Link-down notification
Hi, I have a question regarding some events on many of our switches. The events in question are shown as "link-down notification" followed almost instantly by a "link-up notification". Here's a very small sample of much bigger log file.
↧
Cannot ping/ARP Entries not exist
Hi all, I got problem where I cannot ping server from another server, both connected to the BigIron RX 16. It occur in random time, and in random server. When it occur the ARP entries are not exist on server's ARP table. I have checked
↧
↧
Enable web management login on ICX6610-24P-E switch
Hi There, I am new to brocade switch and recently get 1 pc mentioned box, just did some simple congiruation like the the IP address, default gateway as well as the host name setting. I also tried to enable to https web access, after that I tried to
↧
Link Aggregate Priority HELP please
We have two separate stacks connected via fiber connections. port 1/1/3 is connected to 1/1/3 in the other stack and port 2/1/3 is connected to the other stack's 2/1/3. below is the configuration. right now 1/1/3 connected is saturated
↧
Anyone using cattools to backup VDX switches?
I've been trying to get our existing cattools server to backup our new VDX switches and have had no luck. Ive tried using the brocade template and the foundry template neither one works for the VDX. Anyone got this working yet? Thanks, Pat
↧
Question about enabling a port and changing port state.
I am new to Brocade and have encountered an issue I need assistance resolving. My background is Cisco and am new to the network that I am having an issue on. My senior engineer is out of town today and unavailable to answer my question, I was
↧
↧
Trunk or Link aggregation on Brocade ICX-6450
Hi there, I would like to have group of ethernet 2 ports on my physical Esxi server to be working as a group of ports, I have already configured my Esxi host and selected 'the switch, NIC teaming option' with 'Route based on IP hash' and its put all 2
↧
MLX templates
Does anybody have some good templates for the MLX mpls,bgp,vpls and so on?
↧
Stacking 2 TurboIron 24x's?
Please forgive me as I am new to Brocade. I have 4 sites w/each getting 2 Brocade TurboIon 24x's. On top of them will be 2 Cisco ASA's for the firewall and ids. Now for the top TurboIron, I have 2 copper interfaces trunked going to the ids. I also have 2
↧
Port mirror on FCX-48GS
Hi I'm trying to do a simple port mirroring on an FCX-48GS switch. I want traffic from ethernet 1/1/22 to be copied to ethernet 1/1/43, using the following configuration: switch1-1(config)#mirror-port ethernet 1/1/43
↧
↧
ICX-6450 Odd error message
Hello all -- We're seeing the following error pop repeatedly on one of our ICX-6450-48P edge switches: Error: Module 256 is not a POE module. The switch only has Module 1 and Module 2. The switch is working normally othar
↧
ICX 6610 vrrp-e design with trunk between equipments...
hi everybody! I have an issue with vrrpe implementation, actually I have 2 icx 6610 working as active-active, and issue goes like this: if icx-a is the master for vlan 124 and icx-b is the master for vlan 123 when users on vlan 124 want to
↧
how can I configure ip routing on FWS624G
How can I configure IP routing on switch FWS624G? This is the show version output: sh version Copyright (c) 1996-2010 Brocade Communications Systems, Inc. UNIT 1: compiled on Apr 19 2010 at 16:20:30 labeled as
↧