Hello All. I'm having a problem with an RX4 / BI-4XG. The load on the LP sits at a constant 20-30 with spikes to 70-100, dropping packets increasing latency when it gets there. This RX has 2 4XGs, one with the connection to the
↧
BI-4XG high CPU load
↧
Newbie question about Brocade 1020
I have decided to learn about Fibre networks and I have a Dell Powerconnect 8024F 10GB switch. Managed 10 Gigabit Ethernet Switches | Dell Australia 1. Can the Brocade 1020 dual adapter be used as a general purpose network adapter ie for use in
↧
↧
Backup firmware image from flash
Hi all, I have a FCX-624S, I want to upgrade the firmware image, currently it runs version 07.0.01b. Before making some mistake, I would like to backup both the firmware images installed on the switch now (primary and secondary flash partition). So I
↧
ICX 6430-24p
something as simple as......the default ip address for the ICX 6430-24p switch........anyone???
↧
Question about enabling a port and changing port state.
I am new to Brocade and have encountered an issue I need assistance resolving. My background is Cisco and am new to the network that I am having an issue on. My senior engineer is out of town today and unavailable to answer my question, I was
↧
↧
Trunk or Link aggregation on Brocade ICX-6450
Hi there, I would like to have group of ethernet 2 ports on my physical Esxi server to be working as a group of ports, I have already configured my Esxi host and selected 'the switch, NIC teaming option' with 'Route based on IP hash' and its put all 2
↧
Best way to lock down a switch (only allowed MAC addresses)
Folks, whats the best way to lock down a switch (FCX648GS) to only allow PC's with MAC addresses that I specify? (Mac filtering, mac authentication) ??
↧
MLX line card, available memory issue & questions
A month ago I started noticing this getting logged in my syslog collector: Current Total Free Memory (26841088) on LP 1 is below 5 percent of Installed Memory. After 2 weeks the memory free had decreased maybe 200K, and reading on f-nsp I
↧
ICX-6450 Odd error message
Hello all -- We're seeing the following error pop repeatedly on one of our ICX-6450-48P edge switches: Error: Module 256 is not a POE module. The switch only has Module 1 and Module 2. The switch is working normally othar
↧
↧
sending logging cli-command to only syslog and not to local buffer
I wanted to know if anyone has any experience on how to only send cli-commands logged to only the syslog and not the local buffer. The hardware is a netiron running 5200e. Based on my research it does not appear that this can be done and that once
↧
Admin manual for ICX 6450 48 POE
Anybody know where I can download the administrator's manual for ICX 6450 48 POE switch?
↧
how can I configure ip routing on FWS624G
How can I configure IP routing on switch FWS624G? This is the show version output: sh version Copyright (c) 1996-2010 Brocade Communications Systems, Inc. UNIT 1: compiled on Apr 19 2010 at 16:20:30 labeled as
↧
Management Interface MLXe and 6650ICX
Hi how can i change the vlan of the Management interface on a MLXe ( Version 5.4.) and ICX Switch Thanks in advance regards Sascha_se
↧
↧
Howto configure SSH on brocade 64XX series
I want to activate the SSH login to manage my brocade switch. I'm searching the guide and I don't find the command to activate SSH. Do I need to generate a key ? Can you list me all the command I need to be able to log in using
↧
Max MCT Clients on ICX6650
Hi All Does anybody know how many MCT clients can be configured on ICX6650? Where I can find detailed specification (clients, port/trunk, trunks,….) about MCT on ICX6650? I was searching around - with very little success.
↧
IP SLA feature
Hello, As far as I know there is no such thing in brocade switches....I need that feature because a customer in the Data Center has a Call Manager installed, and we need to measure the performance inside the LAN, from their connection up to the
↧
QoS on FastIron CX switches in a stack
The configuration guide states that: "By default in stacking mode, 802.1p marking is not enabled. Outgoing tagged traffic is not marked with 802.1p in the VLAN tag based on teh internal hardware aueue into which ingress traffic was classified."
↧
↧
ACL on routed VLAN
Have a project that requires specific hosts on a vlan to be secure from the remaining traffic on a pre-existing VLAN (with servers and clients). Is there any way to keep do this thru ACL's without impacting the rest of the traffic on the VLAN??
↧
How to configure adaptive rate-limit on superx
I am trying to configure my FastIron SuperX to limit bandwidth to specific Vlan's. I want to provide the VLAN T1 (1544k) speed and allow for bursts of traffic. I have configured and adaptive rate-limit policy through an ACL and have had some success, but
↧
Latest Software...Boot Err: Bad code image header
I have an FWS648G (no POE) that I updated the boot rom on and when I try to boot it from the primary it says Boot Err: Bad code image header. I have tried re-uploading the flash, erasing and reuploading it. I copied the flash from an FWS648GPOE and
↧