hi all i have some types of brocade switches and routers and it was configured with TEMPERATURE shutdown level 55 but i awant to change this value =============================================== i try this command but i cant find it in
↧
how can i change TEMPERATURE shutdown level
↧
IPv6 DHCP PD
Hi Using CER with 5.1 firmware as DHCPv6 relay. As DHCPv6 server using ISC DHCP6. Customer have a router with ipv6 support. 1.Customer's router are requesting by DHCPv6 IPv6 address for self and IPv6 block for PCs behind
↧
↧
show interface capabilities equilavent for Netirons
Is there a cisco "show interface capabilities" equilavent for Netirons. I need to find out what sfp model is being used on a remote Netiron. Thanks in advance
↧
"Class 3 transmit frames discarded due to timeout"
In the clips from one of my switches that has only one ISL, I am seeing a number of Class 3 trasmit frames discarded due to timeout.sw These error reports are occurring on the ISL. So my question is, how does the switch signal the target
↧
Is there a max on Layer 2 vlan entries in the startup/running config?
I went to go add a new vlan entry on my FastIron LS 648 and got the following messge. error - create L2 vlan 12 failed, no free L2 vlan entry If I remove a vlan currently in the running config it will allow me to add another vlan. I have
↧
↧
Vlan and Link-aggregate
i need helping about vlan and link-aggregate . I want to know if possible tagged a "link-aggregate" in 2 vlan´´s because i have a VMware server (with link-aggregate) in "vlan 20" and one of the VMachine i need stay in another vlan.
↧
TurboIron X24 Extremely Poor Throughput
We have done back to back testing across various servers, transceivers, cables, cards all with the same result. We are barley getting 60MBps through each port. Everything is connected at full 10GB FDX, no errors or dropped frames. In any combination we
↧
What does "latched remote fault" mean?
I have a MLX running Ironware Version 5.2.0bT163. Every time I bring up a certain port I see a message in the log "latched remote fault" right before the up message: Mar 6 23:51:10:I:System: Interface ethernet 5/1, state up
↧
ip helper-address on FastIron Family(ICX, FWS) is not working properly
Hi guys, I experienced an unexpected problem on DHCP installation. the #ip helper-address on ICX-6450 is not working properly. The topology shows as follow Host should have its ip from DHCP-server in another network, so i use
↧
↧
ICX 6450 24 port switch
I have a ICX 6450 24 port switch that I am trying to partition into 2 layer3 vlans. I created vlan 3 and vlan 13 and added untagged ports 3-12 to vlan 3 and 13 to 23 for vlan 13. vlan 3 by port tagged ethe 1/1/1 ethe 1/1/24 untagged ethe
↧
MLX Optical Monitoring
Hello, I've got a bunch of MLXs and I am unable to get any readings for optical monitoring. I have, enabled 'optical-monitor' on the global level and enabled the same on individual interfaces (some accept it stating its
↧
issues with multicast thing (Forefront TMG 2010 in NLB cluster mode)
Let me describe issues with multicasting that we observe on FCX648 (7202e firmware). The term “multicast” usually describes two different situations, i.e. multicast IP addresses and multicast MAC addresses. Let us install Microsoft
↧
Packet drop on MLX with error code "53 IP no route (PFE)"
Hello, I use an MLX-16 for switching and inter-vlan routing. For some days, i've been noticing some communication problems (e.g. Ping failure), that affects only computers that are connected (through an access switch) to Slot 13 of the MLX. No
↧
↧
MPLS-VPLS and BPDUs (MLX/CES/CER)
Hi together, just a theoretical question: What happen in the access-switches in a MPLS enviroment if i configure the same VLAN on - lets say in about 6 locations - and bring them together with one VPLS instance and i would deactivate
↧
Typical braodcast storm
Hi, We recently had a brioadcast storm caused by a loop between non-RSTP capable devices. As expected, as soon as the redundant path was removed, the network recovered within seconds. I was wondering if there's a way to make a port auto
↧
Brocade FWS 624G-POE
hi I have FWS624G-POE switch. does it have a default IP. If not, then do how do i use telnet to configure in the IP thanks RGod
↧
old FastIron EDGE x648
Hi Guys i have an urgent question ... I need to configure the sfps on that switch and i need to know how they correlate to the e-ports... meaning in order to configure 1F - 4F ports .... do i configure E1-E4 ports on the switch? Thanks
↧
↧
ESXi 5.0 nic teaming issue
I am having an issue where I am trying to enable nic teaming on my ESXi 5.0 hosts. When configuring the trunk and then running trunk deploy I am losing connectivity to my host. To get connectivity back I have to remove the trunk. I have the following
↧
BFD with Aggregation Link
how do we configured BFD with aggregation link Ethernet on CES/CER/MLX devices ? lag "1" dynamic id 1 ports ethernet 1/21 to 1/22 primary-port 1/21 deploy interface ethernet 1/21 enable bfd interval 100 min-rx 100 multiplier 3
↧
BGP peering on Old Jetcore switches?
I have some older Jetcore switches that we have in production. These are receiving a "filtered" internet feed. They currently peer with 5 other BGP peers. They have two uplink providers within this mix. I have found that if I have any link changes or
↧